Skip to content

Heat Pump Installation in Culver City, CA

Serving Culver City and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (669) 201-5255

The short answer

A heat pump suits Culver City's mild winters and warm, dry summers, and it can replace both a gas furnace and a central air conditioner. Liberty HVAC Services sizes each system to the house, installs it, and confirms which rebates apply based on the utility that serves your address.

Many Culver City homeowners are replacing an aging gas furnace and a separate air conditioner with a single heat pump that heats in winter and cools in summer. Liberty HVAC Services installs heat pumps in homes across Culver City, including ZIP codes 90230 and 90232, about 3 miles southwest of our Los Angeles base. This page covers how Culver City's climate affects sizing, what happens during an install, and how rebates depend on which utility serves your address.

Why heat pumps fit Culver City homes

Los Angeles has a Mediterranean climate: dry summers, mild winters, and fall Santa Ana winds that can bring hot, dry spells. A heat pump handles all of these. It moves heat out of the house when it is warm and into the house on cool nights, so one outdoor unit covers the whole year.

Heating needs here are modest, so a heat pump rarely has to work at its limits in winter. Cooling matters more. Late-summer heat and Santa Ana spells are when an undersized system falls behind, so we size for those days, not just an average afternoon.

Replacing a gas furnace: what to know first

If your home has a natural-gas furnace nearing the end of its life, check the regional rules before you replace it with another one. South Coast AQMD Rule 1111 limits NOx emissions from natural-gas fan-type central furnaces sold and installed in the Los Angeles region, and the district has been amending it toward zero-emission requirements. The district sets and revises the compliance dates, so anyone planning a furnace replacement should check the current rule.

A heat pump uses no gas, so it avoids that question. Before switching, we look at your electrical panel, the existing ductwork, and where the outdoor unit can go, so you know whether the house is ready or needs work first.

How we install a heat pump in your home

Every installation starts with the house itself. Two homes of the same size on the same block can need very different systems depending on insulation, windows, sun exposure, and duct condition.

Our installation process covers:

  • A load calculation based on your home's size, layout, insulation, and windows
  • An inspection of existing ducts for leaks, damage, and correct sizing
  • A check of the electrical panel and circuit capacity for the new equipment
  • Choosing an outdoor unit location with proper clearance and reasonable distance from bedrooms and neighbors
  • Removing old equipment, setting the new indoor and outdoor units, and connecting refrigerant lines
  • Startup testing of airflow, refrigerant charge, and heating and cooling modes
  • A walkthrough of the thermostat and filter changes before we leave

Ducted and ductless options

If your home already has ductwork in good shape, a ducted heat pump can often use it, with repairs or sealing where needed. This is usually the simplest path when replacing a furnace and central air conditioner.

For homes without ducts, or for an addition, converted garage, or upstairs room that never stays comfortable, a ductless mini-split can heat and cool specific rooms. Some homes use both: a central system plus a ductless unit for a problem area. We'll explain the tradeoffs for your layout.

Rebates and tax credits in Culver City

Culver City is its own city, separate from the City of Los Angeles. Many homes outside the City of Los Angeles are served by Southern California Edison rather than LADWP, so which equipment rebates are available depends on the utility that serves your address. We confirm the current offer before quoting it.

LADWP residential electric customers can apply for Consumer Rebate Program rebates on qualifying heat pump systems, with the amount based on the unit's SEER2/HSPF2 rating. That application is filed after the equipment is purchased and installed, within 12 months of purchase. The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025, and is not available for new installations after that date.

More services in Culver City

Related

What to expect

How a visit goes

  1. Diagnose First

    We test the system and pinpoint the cause before suggesting parts or replacement, so you know what you're paying to fix and why.

  2. Clear Options

    When there's more than one way to solve a problem, we lay out each option, what it involves, and the tradeoffs, then let you decide.

  3. Current Rules and Rebates

    Local equipment rules and utility rebates change. We check the current requirements and the offers available for your address before planning an installation.

FAQ

Common questions

Will a heat pump keep my Culver City home warm in winter?

Yes. Winters in the Los Angeles area are mild, so a properly sized heat pump can heat a home comfortably without backup gas heat in most cases.

Can I keep my existing ductwork?

Often, yes. We inspect the ducts for leaks, damage, and sizing. If they are in reasonable shape, the new system can usually use them after any needed sealing or repairs.

Do I need an electrical upgrade?

It depends on your panel and existing circuits. We check capacity during the assessment and tell you up front if any electrical work is needed.

Which rebates can I get in Culver City?

It depends on the utility that serves your address. Many homes outside the City of Los Angeles are served by Southern California Edison rather than LADWP. We confirm the current offer for your home before quoting it.

Can I still claim the federal tax credit for a heat pump?

No, not for new installations. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025.

Do you serve areas near Culver City?

Yes. Along with Culver City, we install heat pumps in Inglewood, Beverly Hills, Santa Monica, West Hollywood, and El Segundo.

Tell Us What's Going On With Your System

Whether your AC stopped cooling, your furnace won't start, or you're thinking about switching to a heat pump, contact Liberty HVAC Services. We'll ask a few questions, look at the system, and explain your options before any work begins.

Call (669) 201-5255 Request Service