The short answer
Liberty HVAC Services repairs furnaces, heat pumps, and wall heaters in Beverly Hills homes in the 90211 and 90212 ZIP codes. Most winter no-heat calls come from parts that failed while the system sat idle, such as igniters, flame sensors, thermostats, and clogged filters. We diagnose the problem and explain your options before any work starts.
In Beverly Hills, heating problems usually show up on the first cold night of the season, after the system has sat unused for months. Liberty HVAC Services repairs gas furnaces, heat pumps, and wall and floor heaters in homes throughout Beverly Hills, including the 90211 and 90212 ZIP codes. Our base in Los Angeles is about 3 miles away, so getting to your home is a short drive. This page covers what typically goes wrong with heating systems here, what you can safely check yourself, and how we handle a repair from diagnosis to fix.
Why Heating Systems Fail in Beverly Hills Homes
Los Angeles has a Mediterranean climate with dry summers and mild winters. Beverly Hills sits between the coast and the hotter inland valleys, so many homes here run the heat only on cool mornings and evenings for part of the year. That light, seasonal use is easy on equipment in some ways and hard on it in others. Parts that sit idle for months can corrode, dust settles on burners and sensors, and small problems go unnoticed until the heater is actually needed.
Fall Santa Ana winds can also push fine dust into homes, which loads up air filters and coats furnace components right before heating season starts. These are the problems we see most often in local homes:
- Furnace clicks or tries to start but never lights, often a worn hot surface igniter or dirty flame sensor
- Burners light and then shut off after a few seconds
- Blower runs but the air from the vents is cool
- Heat pump runs constantly in heat mode without warming the house
- Burning dust smell that lingers past the first few minutes of use
- Older wall or floor furnaces with pilot lights that won't stay lit
- Thermostats that lost settings or power after sitting unused
Quick Checks Before You Schedule a Repair
Some no-heat calls turn out to be simple fixes. If it's safe to do so, check these items first. If you smell gas, leave the house and call your gas utility from outside instead of troubleshooting anything.
- Make sure the thermostat is set to Heat and the set temperature is above room temperature
- Replace thermostat batteries if the display is blank or dim
- Check the breaker for the furnace or air handler, and the service switch near the unit, which often looks like a light switch
- Look at the air filter and replace it if it's gray or clogged
- Confirm the furnace access panel is fully closed, since many units won't run with it loose
How a Heating Repair Visit Works
Our technician starts by asking what you've noticed, then tests the system while it runs. For gas furnaces, that includes checking ignition, flame quality, gas pressure, venting, and the safety switches that shut the furnace down when something is wrong. For heat pumps, we check the defrost cycle, reversing valve, refrigerant operation, and outdoor coil.
Once we know the cause, we explain it in plain terms and tell you what the repair involves before any work begins. If we find a safety concern, such as a cracked heat exchanger, a blocked flue, or signs of carbon monoxide risk, we'll show you what we found and explain why the unit shouldn't run until it's corrected.
When Replacement Makes More Sense Than Repair
Repair is usually the right call when a single part has failed on a system that's otherwise in good shape. Replacement starts to make sense when the heat exchanger is cracked, repairs keep stacking up, or the system no longer heats the house evenly.
If you're considering a new gas furnace, keep in mind that South Coast AQMD Rule 1111 limits NOx emissions from gas fan-type central furnaces sold and installed in this region, and the district has been amending it toward zero-emission requirements. Compliance dates are set and revised by the district, so check the current rule before you plan a furnace replacement. Many homeowners compare a heat pump at this point instead.
Heat pump rebates depend on which utility serves your address. Many homes outside the City of Los Angeles, which includes Beverly Hills, are served by Southern California Edison rather than LADWP, so we confirm the current offer for your address before quoting it. The federal 25C tax credit for heat pumps ended for equipment placed in service after December 31, 2025, so it doesn't apply to new installations.
Serving Beverly Hills and Nearby Communities
Along with Beverly Hills, we provide heating repair in West Hollywood, Culver City, Santa Monica, Burbank, Inglewood, and across Los Angeles County. If you're not sure whether we cover your street, ask when you schedule.
More services in Beverly Hills
- AC Repair in Beverly Hills
- Heat Pump Installation in Beverly Hills
- AC Installation in Beverly Hills
- Furnace Repair in Beverly Hills

